Network Diagnostics Dialog¶

Use this page to monitor the live network link between AetherSDR and your FLEX-8600, confirm connection addresses, inspect per-stream data rates, and review filtered log output.

Before you start¶

AetherSDR must be running. The dialog does not require an active radio connection, but most fields and graphs will show meaningful values only after a connection attempt has been made.

Opening the dialog¶

Click Settings > Network....
The Network Diagnostics dialog opens. It defaults to the Overview tab.

Tab overview¶

The dialog is organized into seven tabs. Select the tab that matches what you need to inspect.

Tab	What it shows
Overview	Four health cards (Status, Latency, Packet Loss, Audio Buffer) and four time-series graphs (Latency and Jitter, Recent Packet Loss, Total Stream Rates, Audio Buffer).
Details	Scrollable grid with labeled values for Network Status, Incoming Stream Rates, Packet Loss, and Audio Playback groups.
Latency	Full-width time-series graph of RTT, arrival gap, and jitter in ms.
Rates	Full-width log-scale time-series graph of per-stream incoming bitrates (RX total, Audio, FFT, Waterfall, Meters, DAX) in kbps.
Packet Loss	Full-width time-series graph of packet loss % per stream category.
Audio	Full-width time-series graph of playback buffer fill (ms) and underruns/s.
Logs	Live tail of the AetherSDR log file, filtered by category checkboxes. Syntax-highlighted by log level and category name.

Verify the radio's IP and local bind address¶

Open the Network Diagnostics dialog as described above.
Select the Details tab.
Locate the Network Status group.
Read Target Radio IP — this shows the IP address of the radio AetherSDR connected to. If no connection has been made, the field displays Not connected.
Read Selected Source — this shows the local network interface or bind path AetherSDR used to reach the radio.
Read Local TCP and Local UDP to see the exact local endpoints for each protocol.
Click Close when done.

Control the chart timeframe¶

The Timeframe combo box in the top-right corner of the tab bar sets how far back all time-series charts display history. It is hidden while the Logs tab is active.

Value
1 minute
5 minutes (default)
15 minutes
1 hour
1 day
1 week

Select a value from the Timeframe drop-down. All visible charts update immediately.

Use the Logs tab¶

Select the Logs tab.
The Log path label at the top of the tab shows the full path of the log file being tailed.
Use the Filter Categories (Logs) checkboxes to show or hide individual log categories. The list includes a General category (shown by default) plus every category registered with LogManager.
Click Select All (Logs) to enable all categories at once.
Click Deselect All (Logs) to hide all categories at once.
The Live / Paused toggle button controls auto-scrolling:
Live — the viewer auto-scrolls to the newest output as log lines arrive.
Paused — scrolling is stopped so you can read earlier lines. Scroll up at any time to auto-pause.
Click Live to resume and jump back to the tail.
Log lines are syntax-highlighted by log level (DBG, INF, WRN, CRT, FTL) and by category name.

Note: The Timeframe selector is hidden while the Logs tab is active. Switch to any other tab to restore it.

What each indicator means¶

Indicator	Meaning
Status	Overall link quality, color-coded from green (Excellent) to red (Poor). States: Excellent, Very Good, Good, Fair, Poor.
Target Radio IP	IP address of the connected radio. Displays `Not connected` if no connection is active.
Selected Source	Local NIC or bind path used to reach the radio.
Local TCP	Local TCP endpoint (address and port).
Local UDP	Local UDP endpoint (address and port).
First UDP Packet	Whether the first UDP packet has been received since connect (Yes / No).
Latency (RTT)	Current round-trip time.
Max Latency (RTT)	Highest RTT seen since connect.
Audio / FFT / Waterfall / Meters / DAX rates	Per-category ingress rate in kbps.
Total RX / Total TX	Aggregate bytes per second in each direction.
Audio / FFT / Waterfall / Meters / DAX drops	Per-category dropped-packet counts and percentage.
RX Buffer Now / Peak	Current and peak audio buffer fill in bytes and ms.
Underruns (total / last sec)	Audio underrun counters.
Audio Arrival Gap / Max Arrival Gap	Inter-packet arrival timing.
Network Jitter	Smoothed jitter estimate of the audio stream in ms.
Log path label	Full path of the log file being tailed (visible on the Logs tab).

Controls reference¶

Control	Type	Default	Behavior
Timeframe	Combo box	5 minutes	Selects how far back the time-series charts display history. Hidden when the Logs tab is active.
Filter Categories (Logs)	Checkboxes	—	Per-category checkboxes filter the log view. Includes a General category plus all registered LogManager categories.
Select All (Logs)	Button	—	Shows all log categories in the viewer.
Deselect All (Logs)	Button	—	Hides all log categories from the viewer.
Live / Paused (Logs)	Toggle button	Live	When Live, the viewer auto-scrolls to newest output. Scrolling up auto-pauses; clicking Live resumes and jumps to the tail.
Close	Button	—	Closes the dialog.

Tips¶

The dialog refreshes all values once per second. If you have just connected, wait a moment for the fields to populate.
Selected Source is useful when the host has multiple network interfaces. Confirm it shows the interface on the same subnet as the radio, not a VPN or secondary adapter.
The Rates tab uses a logarithmic y-axis, which makes it easier to compare high-bandwidth streams (such as total RX at several Mbps) alongside low-bandwidth streams (such as Meters at a few kbps) on the same chart.
On the Logs tab, scrolling up automatically switches the toggle to Paused. Click Live to jump back to the current tail.

Troubleshooting¶

Target Radio IP shows Not connected — No connection to the radio is active. Use Settings > Connect to Radio... to discover and connect to your FLEX-8600, then reopen the dialog.
Selected Source shows an unexpected interface — Your operating system routed the connection through a different NIC than intended. Check your routing table or disable unused network interfaces, then reconnect.
Status card shows Poor or Fair — Check the Latency and Packet Loss tabs for the affected time range. High jitter or sustained packet loss on the Audio stream usually points to network congestion or Wi-Fi interference.
Logs tab shows no output — All category checkboxes may be deselected. Click Select All (Logs) to restore visibility.